Loading... Please wait...

Our Newsletter


Sony Xploid 800W (XM-D400P5) car amplifier

  • Image 1
  • Image 2
  • Image 3
  • Image 4
Price:
CAD $80.00
Shipping:
Calculated at checkout


Product Description

Class D P5 Amplifiers: The XM-D400P5 amplifier is a 5-sided Class D mono block amp, designed to complement the Sony P5 subwoofer line. Class D technology is a method to convert and amplify music signals with MOSFETs to high-speed pulse signals. Class D amps feature high efficiency and low heat generation.

Protection Circuitry: This amplifier has 3-way protection circuitry which protects the amplifier in the following cases:

  • Thermal: shuts off the amp when the operating temperature is too high
  • Short circuit: shuts off the amp when the speaker outputs are short-circuited
  • DC Offset: shuts off the amp when the speaker wires or ground lead is not securely connected, generating direct current

Power/Protector LED: The amplifier has an LED on the top panel which glows green when operating normally, and changes to red when the protection circuit is activated.

Low-pass Crossover: The XM-D400P5 is equipped with a low-pass crossover, continuously variable from 50-300Hz, with a slope of 12dB/octave. It is constantly activated and cannot be switched off.

Low Boost: You can add up to 10dB of bass boost centered at 40Hz.

Preamp Output: This amplifier includes a stereo preamp output, which allows you to send an unfiltered signal to another amplifier.

Speaker-level Input Harness: The amp comes with a speaker-level input harness with a 4-pin Molex plug on one end. This allows you to more easily connect this amplifier to a factory radio or a receiver without preamp outputs.

Protection Cap: The XM-D400P5 comes with a rubber protection cap that fits over the wire terminal strip, helping to prevent accidental short circuiting.

Inputs and Outputs

Front Center of Amplifier:

  • +12V (power): screw terminal (terminal is 0.54" wide)
  • GND (ground): screw terminal (terminal is 0.54" wide)
  • REM (remote turn-on): screw terminal (terminal is 0.34" wide)
  • Speaker Outputs: 2 pairs of screw terminals (each terminal is 0.34" wide) Note: Although there are two sets of speaker terminals, they are not stereo outputs, but summed (L+R) mono. The speaker outputs are internally wired in parallel, so if you connect two 4-ohm speakers to the amp, the amplifier will "see" a 2-ohm load.

Front Right of Amplifier:

  • Line-In: RCA stereo jacks
  • Line-Out: RCA stereo jacks
  • High Level Input: a 4-pin input for use with the included speaker-level input harness

Specifications

RMS Power Output:

  • 200 watts x 1 into 4 ohms (20Hz to 300Hz, 0.2% THD)
  • 400 watts x 1 into 2 ohms (20Hz to 300Hz, 0.6% THD)

Maximum Power Output:

  • 400 watts x 1 into 4 ohms
  • 800 watts x 1 into 2 ohms

Wiring Recommendation

Amplifier Wiring: This amplifier uses two 30-amp fuses, so its total fuse rating is 60 amps, however Sony recommends using an 80-amp fuse at the battery. The Streetwires 4-gauge amp wiring kits (items 211PS4B, 211PS4R, 211PS4BI, 211PS4RI and 211AK4) include an 80-amp fuse, which will accommodate the amp's fuse rating. Other 4-gauge amp wiring kits carried by Crutchfield include a 60-amp fuse. If you want to use a 4-gauge wiring kit that comes with a fuse rated for less than 80 amps, the fuse should be replaced with an 80-amp AGU fuse (item 211AGU80).

Find Similar Products by Category

Write your own product review

Product Reviews

This product hasn't received any reviews yet. Be the first to review this product!

You Recently Viewed...